Nickel-free IGEPIG process for high-frequency and ultra-fine line applications

Low insertion losses are critical for signal transmission in the high-frequency range. Umicore’s nickel-free IGEPIG layer structure eliminates the potential attenuation caused by a nickel layer

Umicore Electroplating is introducing the IGEPIG process, developed by Uyemura, as its exclusive European distributor. The nickel-free final finish combines a gold seed layer, a palladium diffusion barrier, and a final gold top coat. The process suits electronics applications that require high signal integrity, very narrow line spaces, or flexible copper substrates

As frequencies rise and electronic assemblies shrink, the choice of final finish becomes even more important. Plating systems such as ENIG (electroless nickel, immersion gold) and ENEPIG (electroless nickel, electroless palladium, immersion gold) include a nickel layer between the copper substrate and the outer precious-metal coating. This layer acts as a diffusion barrier and a base for the subsequent layer structure. However, in certain high-frequency, fine-line, and flexible circuit applications, nickel can become a limiting factor.

Nickel-free layer structure with a palladium diffusion barrier

To provide the necessary functions without a nickel layer, the standard IGEPIG process combines a catalytically active, 20-nanometer-thick gold seed layer with a 100-nanometer-thick, chemically deposited palladium layer and a final 80-nanometer-thick gold top layer.

The gold seed layer provides the catalytic basis for homogeneous, controlled palladium deposition. The palladium layer acts as a diffusion barrier between copper and gold, preventing copper diffusion into the functional gold layer. This is important for final finishes exposed to thermal stress. The final gold top layer protects the underlying palladium and provides the properties for further processing.

The XPS analysis following thermal exposure clearly shows that the palladium layer acts as a diffusion barrier in the nickel-free IGEPIG process.

High frequency, ultra-fine line spaces and flexible copper substrates

At high frequencies, nickel-containing intermediate layers can attenuate electrical signals because of nickel’s ferromagnetic properties. This effect can become more significant as frequency increases, since the skin effect concentrates the current increasingly on the conductor’s surface. For applications where reducing transmission losses is critical, a nickel layer can be a limiting factor.

The nickel-free structure also provides advantages for very fine line and space geometries. The IPC specifications 4552 for ENIG and 4556 for ENEPIG stipulate a nickel layer thickness of three to six micrometres to ensure an effective diffusion barrier.

As structures become smaller, this nickel layer reduces the available spacing between neighbouring lines. Added to this is the activator system required for electroless nickel plating. For line spaces under 50 micrometres, activator residues can cause footing or stray plating, increasing the risk of short circuits. Because IGEPIG does not require a nickel layer or the associated activator system, it reduces these process-related risks. To date, IGEPIG has been used to plate line spaces of less than 20 micrometres without stray plating or bridging.

The IGEPIG process can successfully coat line spaces of less than 20 µm.

Additionally, eliminating the relatively low-ductility nickel layer makes IGEPIG a suitable final finish option for flexible copper substrates. Nickel can limit the mechanical flexibility of the plated copper; as a result, a nickel-free final finish is also relevant for applications where flexible copper surfaces must be reliably plated and subsequently subjected to mechanical stress.

Solder joint reliability in a comparative test

The new layer structure must also ensure the final finish’s functional reliability. Therefore, IGEPIG solder joint reliability was evaluated using ball grid array (BGA) shear tests.

Under the test conditions used, IGEPIG and the established ENEPIG system achieved the highest shear forces among the variants examined. This remained even after four hours of thermal exposure at 155 degrees Celsius. The results reveal that, under these test conditions, IGEPIG achieves solder joint reliability comparable to ENEPIG.

The BGA shear test shows that IGEPIG achieves a level of solder joint reliability comparable to that of ENEPIG.

Andreas Gross, division manager PCB-Processes at Umicore Electroplating, said, “With IGEPIG, we bridge the gap between simple nickel-free gold surfaces and the established ENEPIG system. Users receive a nickel-free final finish with a palladium diffusion barrier and can tailor the layer structure specifically to the electrical, geometric and thermal requirements of their application without compromising functionality.”

IGEPIG and DIG: a gold bath for both final finishes

Not every application requires the additional palladium diffusion barrier provided by the IGEPIG system. For applications with lower thermal or functional requirements, DIG (Direct Immersion Gold) without a diffusion barrier may still be the technically and economically suitable, nickel-free solution. Umicore combines both final coatings in a flexible 2-in-2 process concept.

A single gold bath supports three deposition steps:

  • The gold seed layer
  • The final gold top layer in IGEPIG
  • Direct gold deposition in DIG

This lets users choose between the two final finishes based on their requirements, without needing an additional gold bath for DIG.

Umicore Electroplating supports customers in the technical and economic evaluation and the implementation of IGEPIG. The offering includes test plating for initial investigations, application-specific economic analyses, consulting on the required process landscape and equipment technology, and support during process implementation. On this basis, it is possible to determine whether IGEPIG is the appropriate final finish for the application.

Share This Article
Leave a Comment